Epoxy.com Product #100m1 Moisture Insensitive Epoxy Primer for use over new (green) concrete

Epoxy.com Logo - Epoxy, Polyurethane, Polysulfide, Polyester, MMA - Methyl Methacrylate and other Construction Resin Systems - Over 350 Products- Since 1980
[Contact Us]

Epoxy.com Product 100MR

Moisture Tolerant Epoxy Primer and Base Coat

Can be Used as a Primer Over Concrete as New as 5 Days


Epoxy.com Product 100MR Moisture Tolerant Primer and Base Coat consists of a unique water based epoxy technology which allows the contractor to install epoxy resin floor systems and other moisture sensitive floor coverings on new concrete (5 days old) without fear of moisture entrapment. Epoxy.com Product 100MR Moisture Tolerant Primer and Base Coat is applied in a two coat application. Epoxy.com Product 100MR Moisture Tolerant Primer and Base Coat is the primer/basecoat used in various Epoxy.com Products

Epoxy.com Product 100MR Moisture Tolerant Primer and Base Coat is a unique two-component, moisture tolerant, extremely high density, chemically enhanced epoxy based product which reduces the passage of water vapor and moisture through slabs on, above or below grade, thus eliminating delamination and blistering of adhesives, floor coverings, resin floor systems, epoxy terrazzo and coatings.

Epoxy.com Product 100MR Moisture Tolerant Primer and Base Coat controls water vapor transmission levels for the installation of most floor covering systems, including VCT, sheet vinyl, carpets, wood, laminates, epoxy resin flooring and epoxy terrazzo.

Advantages

  • Vapor and water barrier.
  • Can be placed on new concrete in as little as 5 days.
  • Water based - low VOC.
  • Highly moisture tolerant
  • Barrier against radon and other gasses
  • Compatible with most flooring systems - conventional, and seamless epoxy flooring systems.
  • Does not support the growth of mold.
  • Easy to install with little down time.

Considerations

  • Substrate must be at least 50° F during installation and curing
  • Substrate must be free of dirt, sealers, waxes, and other foreign materials that would interfere with proper bonding.
  • Must be installed a minimum of 1/8 for use with moisture sensitive floor coverings.

Color Selection

Epoxy.com Surface Preparation Guide Epoxy.com Epoxy Color Chart Here

Can be used clear with Epoxy.com Colored Quartz or Epoxy.com Flooring Flakes. Color packs are available in selected colors. Color pack mix ratio is 1 QT color pack per 5 gallon pail of Epoxy.com Product #697 Methyl Methacrylate (MMA) Binder Resin.

Available in selected colors using color pigment packs 1 to 2 quarts per 5 gallon unit.

Application

Surface preparation

Surface preparation is the most critical portion of any successful resinous flooring system application. All substrates must be properly prepared as outlined in Epoxy.com Surface Preparation Procedures. Epoxy.com Technical Support Department is pleased to answer any questions.

Mixing

Epoxy.com Product 100MR Moisture Tolerant Primer and Base Coat is a two-component material. Do not alter mixing ratios in any way. Part I and Part II are supplied in the correct mixing ratios. Always mix a complete unit in the proportions supplied.

Stir material for approximately 3-4 minutes to form a homogenous consistency using a slow speed drill and �Jiffy� blade. Do not entrap excessive air. Scrape all sides and bottom of container to ensure thorough mixing.

Priming

Prime using Epoxy.com Product 100MR Moisture Tolerant Primer and Base Coat thinned 10% with one (1) pint of potable water per 1.25 gallon unit for good penetration. Apply with a squeegee and short nap roller to the properly prepared substrate. Back roll with the short nap roller to achieve a uniform coverage. Allow to cure hard enough for foot traffic, about 3-4 hours at 75 degrees F.

Body Coat

Apply one (1) Part of Epoxy.com Product 100MR Moisture Tolerant Primer and Base Coat to 4 parts of B. Thoroughly mix with a low speed drill and Jiffy blade until uniform. Mix with low speed drill until uniform and no lumps.

trowel or similar squeegee. Allow to self-level and backroll with a looped roller. A 1.25 gallon unit will cover 30 sq. ft. @ 1/16�.

Broadcast surface with broadcast sand to excess (30-50 lbs./100 sq. ft.) with Epoxy.com Product #77 to achieve 1/8 inch. Sweep and vacuum excess or loose sand after hardening (16-24 hours, depending on temperature).

Top Coatings and Overlays

Apply top coatings or resin floor system directly over broadcast surface. Prime surface with appropriate Epoxy.com primer as required. For vinyl flooring and other floor coverings consult with manufacturer of floor covering.

Physical Properties

Material 2-component epoxy
Density 12.70 lbs/gallon
VOC Content, Mixed < 1 g/L
Solids by Volume59%
Flash Point: Part A
Part B
>212°F
170 °F
Mixing Ratio 1:4 by Vol.
Pot Life, Approximate     60 minutes @ 75°F (24°C)
Open to Foot Traffic After 16 hrs. at 73°F (23°C)
Curing Temperature Minimum 50°F
Full Cure and Maximum Resistance7 days
Hardness, Shore D ASTM-D-2240    70-75
Compressive Strength  ASTM-C- 579   6500 psi
Flexural Strength ASTM-C-580 2100 psi
Adhesion To:
-New concrete (5 days)
-Moist concrete (28 days)
-Dry concrete (28 days)

110 psi
550 psi
580 psi
Temperature Resistance:
a)Continuous:
-Dry heat
-Humid
b)Intermittent:
-High pressure water
-Dry heat


140°F (60°C)
113°F (45°C)

185°F (85°C)
149-185°F (65-85°C)

Maintenance

After completing the application of Epoxy.com Product 100MR Moisture Tolerant Primer and Base Coat and the topcoats or floor covering system, the installer should provide the owner with maintenance instructions relevant to the specific topcoats or floor covering. If floors become slippery due to animal fats, oil, grease, or soap film, clean and rinse thoroughly.

Proper mixing and installation is critical to the optimal success of all product.  See Installation Tips, Techdata, & MSDS for more details on our products.  Be sure to contact us with any questions and/or concerns that you have.

For more information please contact:

Epoxy.com
A Division of Epoxy Systems, Inc
20774 W. Pennsylvania Ave.
Dunnellon, Florida 34431
Hundreds of Systems,
Since 1980 - 35 years
Florida & Vermont
USA


Customer and Technical Support Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time).
Closed 12 Noon-1PM Eastern Time for Lunch

321-206-1833  Customer Service - Ordering and Order Status
                         Katey Fontaine, VP - Customer Service Director
                         sales@epoxy.com

                        Technical Support
352-533-2167  Norm Lambert, President - Technical Support Director 
                         info@epoxy.com

352-489-1666  Accounting and Administration
                         Debby Lambert, CEO, and CFO
                         office@epoxy.com

352-489-1625   Fax line to all Departments

We accept MasterCard, Visa, American Express, Discover, Wire Transfers, and Cashiers Checks

Copyright © 1994-2015 - Epoxy Systems Inc. DBA Epoxy.com  - Commercial, Industrial, and Residential Resins Since 1980

/