Epoxy.com Product #101 - Epoxy Slurry Resin

Epoxy.com Logo - Epoxy, Polyurethane, Polysulfide, Polyester, MMA - Methyl Methacrylate and other Construction Resin Systems - Over 350 Products- Since 1980
[Contact Us]

Epoxy.com Product #101

Epoxy Body Coat

Epoxy Slurry and Epoxy Self Leveling Coating (paint)


Description

Epoxy.com Product #101 Epoxy Body Coat is an epoxy coating for commercial and light industrial floors. Epoxy.com Product #101 Epoxy Body Coat is designed for slurry and self-leveling epoxy flooring applications. Epoxy.com Product #101 Epoxy Body Coat helps to smooth seamless epoxy floors that are to receive Epoxy.com Seamless Epoxy Flooring and Epoxy.com Seamless Epoxy Coating (paint) systems. Epoxy.com Product #101 Epoxy Body Coat provides an extra thickness to protect the substrate from chemical attack. Epoxy.com Product #101 Epoxy Body Coat protects the substrate from impact and adds additional abrasion resistance to Epoxy.com Seamless Epoxy Flooring and Epoxy.com Seamless Epoxy Coating (paint) systems.

Advantages

  • 100% Solids, Zero (0) VOC, means it meets even the strictest low VOC standards
  • Cost Effective
  • Very Low Odor - Zero (0) VOCs means it meets even the toughest low VOC standards
  • Low Viscosity - means it has excellent wetting and self-leveling properties
  • Can be used to level and smooth floors
  • Can be made anti-skid most Epoxy.com Epoxy Anti-Skid Coatings (paints) or Epoxy.com Anti-Skid Epoxy Flooring System.

Consideration

  • Normal Cured Epoxy.com Product #101 requires a minimum temperature of 50° F. to cure. If it will be below 50° F. please contact Epoxy.com for information low temperature cure.
  • Substrate must be clean and sound.
  • Slight color variation from batch to batch. So typically you will need to seal this with an Epoxy.com Coating

Composition

Epoxy.com Product #101 Epoxy Body Coat is a 100% solids Zero (0) VOC epoxy resin and epoxy hardener system.

Application

Surface preparation is the first critical step to the installation of a quality seamless flooring system. All substrates to receive Epoxy.com Product #101 Epoxy Body Coat, should be properly prepared. See Epoxy.com Surface Preparation Guide for more details

Installation will vary by application.  Contact Epoxy.com Technical Support Department for additional information.

Physical Properties

ColorLight Grey, Brick Red, White, & Buff
(other colors by request, subject to minimum quantity and/or upcharge)
Weight/gallon10.50-11.0 mixed
Solids Content     100%
Mix Ratio4A to 1B by volume
Pot Life45 minutes @ 70° F
Viscosity1500 cps, mixed approx.
VOCZero(0)

Dry Time

10-20 mil Film10-14 hours
Light Traffic16 hours
Ultimate Cure @ 74° F  5 days
                       @50° F14 days

Chemical Resistance

   
Reagent Rating
Acetic Acid 5% R
Ammonium Hydroxide 10% R
Citric Acid 5% R
Coca-Cola Syrup R
Crude Oil R
Diesel Fuel R
Ethylene Glycol R
Isopropyl Alcohol R
Ketchup R
Mineral Oil R
Sodium Hydroxide 5% R
Tri-sodium Phosphate 5% R
Urea 6.6% R
R = continuous service
L = Limited Recommendation, occasional spills

Performance Properties

Tensile Strength ASTM-C-3072,300 psi
Smoke Deposited ASTM E-1624 mg. max.
Flame Spread ASTM-16225 max.
Shrinkage ASTM C-531<0.5%
Thermal Coefficient of Expansion ASTM C-531     17.4 x 10-6 in./in./°F
Adhesion - ACI-503R300 psi (100% concrete failure Type I)
Hardness ASTM-D-224075 (Shore D)
Abrasion, Taber CS-17 ASTM-D-40600.065 g loss
Resistance to Elevated TemperaturesNo slip or flow at required temperatures
Impact Resistance MTI-D-3134J Withstands 16ft./lbs. no cracking, delamination or chipping
Indentation MIL-D-3134JWithstands 2,000 lbs./sq.in. for 30 min. without indentation.
Heat Deflection Temperature ASTM D-648110°F
Moisture Absorption<1%
Flexural Strength ASTM-C-5805,000 psi
Compressive Strength ASTM-C-579, 25 Day Cure12,000 psi

Proper mixing and installation is critical to the optimal success of all product.  See Installation Tips, Techdata, & MSDS for more details on our products.  Be sure to contact us with any questions and/or concerns that you have.

For more information please contact:

Epoxy.com
A Division of Epoxy Systems, Inc
20774 W. Pennsylvania Ave.
Dunnellon, Florida 34431
Hundreds of Systems,
Since 1980 - 35 years
Florida & Vermont
USA


Customer and Technical Support Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time).
Closed 12 Noon-1PM Eastern Time for Lunch

321-206-1833  Customer Service - Ordering and Order Status
                         Katey Fontaine, VP - Customer Service Director
                         sales@epoxy.com

                        Technical Support
352-533-2167  Norm Lambert, President - Technical Support Director 
                         info@epoxy.com

352-489-1666  Accounting and Administration
                         Debby Lambert, CEO, and CFO
                         office@epoxy.com

352-489-1625   Fax line to all Departments

We accept MasterCard, Visa, American Express, Discover, Wire Transfers, and Cashiers Checks

Copyright © 1994-2015 - Epoxy Systems Inc. DBA Epoxy.com  - Commercial, Industrial, and Residential Resins Since 1980

/