Flexible Epoxy

Epoxy.com Logo - Epoxy, Polyurethane, Polysulfide, Polyester, MMA - Methyl Methacrylate and other Construction Resin Systems - Over 350 Products- Since 1980
[Contact Us]

Epoxy.com Product #32

100% Solids Flexible Epoxy Membrane& Mortar

Epoxy Crack Isolation System for most Epoxy.com Flooring and Coating Systems


Epoxy.com Product #32 Flexible Epoxy is a flexible resin used as an epoxy membrane and as a flexible epoxy mortar. Epoxy.com Product #32 Flexible Epoxy is a two component, 100% solids epoxy used as a base in many Epoxy.com Flexible Epoxy Floor and Mortar Systems. Flexible Epoxy resists cracking caused by horizontal substrate movement, providing a crack resistant, resilient, sound absorbent, waterproof, durable floor.

Epoxy.com Product #32 Flexible Epoxy offers stress-relieving properties for floor slabs that show movement or vibration. Product #32 Flexible Epoxy is excellent for use in areas such as mechanical equipment rooms, large animal rooms and activity centers.


  • Crack Resistant - Elasticity Allows Substrate Movement
  • Ultimate Elongation of 100%
  • Moisture Insensitive
  • Reduces Noise Created by Mechanical Vibrations
  • Waterproof
  • Good Shock Absorption Qualities
  • Good Chemical Resistance


Surface must be clean and sound. Remove all dirt, laitance, grease curing compounds and other foreign matter by sandblasting, shot blasting, or mechanical abrasion. Remove water and dust from all surfaces with an oil-free blast immediately prior to application. See Epoxy.com Surface Prepartion Guide for more details.


Application of Epoxy.com Product #32 Flexible Epoxy can be applied with brush roller or spray. When spraying back-roll to ensure good contact with surface. Two coats at a minimum thickness of 20 mils each (80 square feet per gallon) is recommended. Do not use in temperatures below 50 degrees F, as cooler temperatures delay hardening.


Prolonged or repeated exposure may cause eye and skin irritation. If contact occurs, wash immediately and seek medical help. Use safety glasses with side shields and wear protective rubber gloves.


All tools and equipment should be cleaned before the system gels. Use MEK, Acetone, or any lacquer solvent.


Mix Ratio 1:1 by volume
Gel Time 40 minutes
Color Gray, Clear
Viscosity (mixed) 2,200 CPS
Initial Cure 8 hours
Final Cure 48-72 hours
Tensile Strength (ASTM D-412) 1000 p.s.i
Ultimate Elongation (ASTM D-412) 100%
Adhesion (unprimed - ASTM D-904) 30 pli
Adhesion to Concrete (ACI Committee 403) 250 p.s.i (Concrete Fails)
Hardness Shore A (ASTM D-2240) 70-80
Impact Resistance (ASTM D-2794) 16 ft. lbs.

Proper mixing and installation is critical to the optimal success of all product.  See Installation Tips, Techdata, & MSDS for more details on our products.  Be sure to contact us with any questions and/or concerns that you have.

For more information please contact:

A Division of Epoxy Systems, Inc
20774 W. Pennsylvania Ave.
Dunnellon, Florida 34431
Hundreds of Systems,
Since 1980 - 35 years
Florida & Vermont

Customer and Technical Support Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time).
Closed 12 Noon-1PM Eastern Time for Lunch

321-206-1833  Customer Service - Ordering and Order Status
                         Katey Fontaine, VP - Customer Service Director

                        Technical Support
352-533-2167  Norm Lambert, President - Technical Support Director 

352-489-1666  Accounting and Administration
                         Debby Lambert, CEO, and CFO

352-489-1625   Fax line to all Departments

We accept MasterCard, Visa, American Express, Discover, Wire Transfers, and Cashiers Checks

Copyright © 1994-2015 - Epoxy Systems Inc. DBA Epoxy.com  - Commercial, Industrial, and Residential Resins Since 1980