Epoxy.com Product #488 - 98% Solids Aliphatic Polyurethane Coating

Epoxy.com Logo - Epoxy, Polyurethane, Polysulfide, Polyester, MMA - Methyl Methacrylate and other Construction Resin Systems - Over 350 Products- Since 1980
[Contact Us]

Aliphatic Polyaspartic Polyurea Coating

 Product #488 - 98% Solids


DESCRIPTION

Product #488 is a two component, ultra high solids, aliphatic polyaspartic polyurea designed to provide high gloss, UV stable (non-yellowing) and chemical resistant protection. Product #488 two component, ultra high solids, aliphatic polyaspartic polyurea is a superior, new generation product exhibiting fast cure time and excellent stain resistance.

Product #488 aliphatic polyaspartic polyurea has very low odor and can be applied indoors in occupied areas. Product #488 aliphatic polyaspartic polyurea is generally used as a clear or pigmented high gloss finish  over decorative and industrial flooring systems.

ADVANTAGES

  • VOC compliant
  • Excellent abrasion resistance
  • Fast set times
  • Chemical & stain resistant
  • Excellent UV resistance
  • Low odor-used in occupied areas
  • High gloss

CONSIDERATIONS

  • Substrate temperature must be a minimum of 50oF
  • Substrate must be free of dirt, waxes, curing agents and other foreign materials
  • Do not apply over damp or wet substrates
  • Avoid applications on surfaces with active moisture vapor transmission
  • Very fast set (short working time)

COMPOSITION

Two Component, Catalyzed Polyaspartic Polymer

APPLICATION

SURFACE PREPARATION

Surface Preparation is the most critical portion of any successful resinous flooring system application. All substrates must be properly prepared as outlined in Epoxy.com's Surface Preparation Guide. Epoxy.com technical service department is pleased to answer any questions.

INSTALLATION

Product #488 aliphatic polyaspartic polyurea is a two component material (2 parts A to 1 part B by Vol.). Add Part B to Part A while mixing, using a slow speed mechanical mixer (Jiffy mixer). Mix until a homogeneous mixture is obtained (approximately 3 minutes). Use care to scrape sides and bottom of container to ensure that no unmixed material remains. Do not whip too much air into the material which may result in pinholes or blisters. Do not mix more material than can be used in 10-15 minutes.

Product #488 aliphatic polyaspartic polyurea will begin to increase in viscosity immediately after mixing and will double in viscosity within 17-20 minutes. Material should be in place at this point.

Immediately after mixing, pour material on floor in a ribbon and spread with a flat trowel or notched squeegee depending on thickness of application. Typical application is 8-12 mils (130-200 sq/gal.). Backroll spread material gently with a short nap mohair roller. Do not over roll and entrap air. Total application time should take no longer than 15 minutes.

Up to 5% solvent (xylene, MEK or similar) may be added at time of mixing to slightly lower viscosity and lengthen pot life.

Product #488 aliphatic polyaspartic polyurea will be tack-free in 2-2 ½ hours at 70oF and 50% relative humidity. Allow 4 hours between coats if applying more than one coat. Light pedestrian traffic is possible after 4 hours, 24-48 hours before heavy pedestrian or automotive traffic. Product #488 aliphatic polyaspartic polyurea is highly stain resistant and hot tire resistant after 48 hours.

CLEAN-UP

Clean skin with soap and water. Tools and equipment should be cleaned with xylene or lacquer thinner.

COVERAGE

Product #488 aliphatic polyaspartic polyurea is typically spread at 160 ft2/gallon to yield 8-10 mils. Up to 15 mils is possible in one application but will exhibit a longer set time.

COLOR

Product #488 aliphatic polyaspartic polyurea is available in Clear. For colors pigment packs must be purchased.  

TECHNICAL DATA

Viscosity @ 75°F Part A 175-200cps
  Mixed A&B 350-400 cps
Mixing Ratio 2 Part A to 1 Part B by Volume
Solids Content 95-97%
Volatile Organic Content .03#/gal. (35.8 gm/l)
Weight per gallon 8.77

CURE/DRY TIME

Pot Lift (Working time)75°F 15-17 minutes
Dry to Touch, 75°F 2.0-2.5 hours
Re-Coat 4 hours
Light Service 4-5 hours
Heavy Traffic 48 hours

TYPICAL PHYSICAL PROPERTIES

Hardness - Shore D ASTM-D-2240 24 hours 25-30
    48 hours 55-60
Tensile Strength. psi ASTM-D-412   3,000-4,000
Elongation, %    ASTM-D-412   50 max

CHEMICAL RESISTANCE

REAGENT

RATING

Acetic Acid-10%, 30% L
Acetone L
Ammonia Hydroxide-38% R
Beer R
Bleach L
Brake Fluid L
Citric Acid-30% R
Citric Acid-40% L
Crude Oil R
Diesel Fuel R
EEP Solvent L
Ethanol L
Ethylene Glycol R
Fatty Acids L
Gasoline R
Hydrochloric Acid-15% R
Hydrogen Peroxide-30% L
Iodine L
Isopropanol R
Jet Fuel R
Lactic Acid-15% R
Lactic Acid-50% R
Methyl Ethyl Ketone L
Nitric Acid-10% L*
Orange Juice R
Phosphoric Acid-85% L
Skydrol L
Sodium Hydroxide-50% R
Sulfuric Acid-20% R
Toluene L
Urea R
Urine R
Vinegar R
Xylene L

R-Recommended for continuous service

L-Limited Recommendation, occasional spills

*-May cause slight stain or discoloration

MAINTENANCE

After completing the application of Product #488 aliphatic polyaspartic polyurea, the installer should provide the owner with maintenance instructions.

Product #488 aliphatic polyaspartic polyurea is easily cleaned with neutral soaps or detergents.

BLOG POSTS & NEWS

You can find more information on Polyurethane Products, and many of our other products at news.epoxy.com.

 Skip Navigation Links

Epoxy.com Home PageExpand Epoxy.com Home Page

Proper mixing and installation is critical to the optimal success of all product.  See Installation Tips, Techdata, & MSDS for more details on our products.  Be sure to contact us with any questions and/or concerns that you have.

For more information please contact:

Epoxy.com
A Division of Epoxy Systems, Inc
20774 W. Pennsylvania Ave.
Dunnellon, Florida 34431
Hundreds of Systems,
Since 1980 - 35 years
Florida & Vermont
USA


Customer and Technical Support Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time).
Closed 12 Noon-1PM Eastern Time for Lunch

321-206-1833  Customer Service - Ordering and Order Status
                         Katey Fontaine, VP - Customer Service Director
                         sales@epoxy.com

                        Technical Support
352-533-2167  Norm Lambert, President - Technical Support Director 
                         info@epoxy.com

352-489-1666  Accounting and Administration
                         Debby Lambert, CEO, and CFO
                         office@epoxy.com

352-489-1625   Fax line to all Departments

We accept MasterCard, Visa, American Express, Discover, Wire Transfers, and Cashiers Checks

Copyright © 1994-2015 - Epoxy Systems Inc. DBA Epoxy.com  - Commercial, Industrial, and Residential Resins Since 1980

/