Epoxy.com Logo - Epoxy, Polyurethane, Polysulfide, Polyester, MMA - Methyl Methacrylate and other Construction Resin Systems - Over 350 Products- Since 1980
[Contact Us]

100% Solids Low Viscosity Low Mod Injection Resin

Epoxy.com Product #301


DESCRIPTION

Epoxy.com Product #301 is a 100% solids low viscosity epoxy adhesive used to restore cracked structural concrete by the pressure injection method and to grout cracks in a horizontal plane by gravity.

ADVANTAGES

  • Moisture insensitive
  • Low viscosity – exceptional flow characteristics
  • High Strength

APPLICATION PROCEDURES

Surface Preparation for Epoxy

Surface must be clean and sound. Interfaces of cracks must he free of dirt, laitance, grease, curing compounds and other foreign matter. Flushing with water through ports under pressure may he necessary prior to epoxy injection. Cracks may be damp or wet.

Epoxy Mixing Directions

Temperature of Epoxy.com™ Product #301 must he 40°F. or above at time of mixing. Stir each component separately before blending. Best if used in an automatic binary mixing system. If mixed manually mix two parts by volume of Part A with one part by volume of B for three minutes with a low speed electric drill motor equipped with a mixing paddle.

Application Epoxy Injection Resin

For pressure injection set ports at intervals that approximately equal the thickness of the member to be injected in inches. Ports may need to place closer together for very fine cracks, or may be slightly further for wider cracks. Seal between and around each port with Epoxy.com Product #5, or #6. Inject Product #301 from an epoxy injection machine or binary hand or pneumatic injection gun. For more information consult Epoxy.com™ technical service department.

Limitations of Epoxy Injection Resin

Minimum substrate temperature must be 40° F.

///

Cleaning Epoxy Injection Resin from Tools

All tools and equipment should be cleaned before the system gels. Use methyl ethyl ketone or any lacquer solvent.

Specifications

Meets ASTM C-881 Type III, Grade 1 Class B and C std. spec.

Mix Ratio 2:1 By Volume
Viscosity 400-450 cps
Initial Cure 6 - 8 hours (with normal cure hardener)
Recoat (coating system) 10-12 hours (regular cure) :4-6 hours (fast cure)
Final Cure 24 hours
Potlife 30-40 minute (with regular cure hardner)
Packaging (unit size) 3 gal unit, 15 gal unit, 165 gallon unit
Standard Colors clear
Colors  Clear - Can be pigmented at an additional charge to make it easier to see when pumping.

 

Elongation (ASTM D-638) Greater than 10%
Compressive Strength (ASTM D-695) 10,000 PSI (min)
Tensile Strength (ASTM D-790) 3,500 PSI
Concrete Bond Strength (ASTM C-882) 2,290 PSI
Shrinkage (ASTM C-883) Passed Test
Thermal Compatibility (ASTM C-884) Passed Test
Adhesion to Concrete (ACI Committee 403) 250 PSI (concrete fails)

Proper mixing and installation is critical to the optimal success of all product.  See Installation Tips, Techdata, & MSDS for more details on our products.  Be sure to contact us with any questions and/or concerns that you have.

For more information please contact:

Epoxy.com
A Division of Epoxy Systems, Inc
20774 W. Pennsylvania Ave.
Dunnellon, Florida 34431
Hundreds of Systems,
Since 1980 - 35 years
Florida & Vermont
USA


Customer and Technical Support Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time).
Closed 12 Noon-1PM Eastern Time for Lunch

321-206-1833  Customer Service - Ordering and Order Status
                         Katey Fontaine, VP - Customer Service Director
                         sales@epoxy.com

                        Technical Support
352-533-2167  Norm Lambert, President - Technical Support Director 
                         info@epoxy.com

352-489-1666  Accounting and Administration
                         Debby Lambert, CEO, and CFO
                         office@epoxy.com

352-489-1625   Fax line to all Departments

We accept MasterCard, Visa, American Express, Discover, Wire Transfers, and Cashiers Checks

Copyright © 1994-2015 - Epoxy Systems Inc. DBA Epoxy.com  - Commercial, Industrial, and Residential Resins Since 1980

/