Epoxy.com Logo - Epoxy, Polyurethane, Polysulfide, Polyester, MMA - Methyl Methacrylate and other Construction Resin Systems - Over 350 Products- Since 1980
[Contact Us]

Chemical & Heat Resistant Epoxy

Product #OSVX3110


DESCRIPTION

Chemical & Heat Resistant Coating is a two component; highly cross linked Novolac, that is 100% solids.  It can be brush, roll or airless spray applied coating designed to provide cavitation, corrosion and erosion resistance to concrete, metallic and nonmetallic surfaces.  PRODUCT #OSVX3110 acts as an inert barrier against extremely harsh environmental factors such as low and high PH, temperature extremes, dry and fluid particulate flow and corrosive chemical attack.  Link to related and similar products. PRODUCT #OSVX3110 Chemical and Heat Resistant epoxy supersedes Epoxy.com Product #634.

USES

  • FGD scrubber ducts
  • Floor coating
  • Condensers
  • Tanks and vessels
  • De-min concrete pads
  • Heat exchangers
  • Water boxes

PHYSICAL PROPERTIES

Finish High Gloss
Color Gray
Specific Gravity 1.27
Pot Life 45 minutes @ 77°F
Dry Time 4 hours @ 770F
Recommended Film Thickness 30 mils/min.; 
40 mils/nominal;
45 mils/max.
Coverage Rate One gallon covers approximately 53.4 square feet at 30 mils
Flash Point Above 2000F

CURED PROPERTIES

Compressive Strength (ASTM D-695/7 Days) 14,000 p.s.i.
Flexural Strength (ASTM D-790/7 Days) 13,000 p.s.i.
Tensile Strength (ASTM C-190/7 Days)  7,500 p.s.i.
Shear Strength (ASTM D-1002 Tensile: Steel to Steel) 2,300 p.s.i.
Operating Temperature Wet:  3000F
Dry:   4000F
PH Range 0.5-13.5

CHEMICAL RESISTANT PROPERTIES

The following represents percent flexural strength retained after two weeks cure at 770F followed by 30 days immersion in the chemical environment as described.

  @770F @ 1400F
45% Nitric Acid 100% + min. 100% + min.
25% Acetic Acid 100% + min. 100% + min.
35% Hydrochloric Acid 100% + min. 100% + min.
20% Sulfuric Acid 100% + min. 100% + min.
15% Sodium Hypochlorite 100% 97%
50% Potassium Hydroxide 100% + min. 100% + min.
30% Sodium Hydroxide 100% + min. 100% + min.
50% Sodium Hydroxide 99% 97%

 


The following standards may be used in assessing what activities can be carried out after an application of PRODUCT #OSVX3110.

Temperature 750F
Overcoating 2 to 4 hours
Movement/Light Stress 8 hours
Traffic Bearing 16 to 24 hours
Immersion/Full Chemical Exposure 5 days

Force cures may be used to either enhance chemical resistance or to allow the coating to be placed in service before 5 days. Allow a post cure of 12 to 24 hours before force curing.


RECOMMENDED FORCE CURE SCHEDULE

  • Minimum 2 Hours @ 1500F
  • Minimum 4 Hours @ 2000F

NOTE:   This product will cure well at temperatures as low as 40 - 450F. However, additional curing time must be provided.

SURFACE PREPARATION

CONCRETE: Surface must be clean and sound. Remove all dirt, laitance, grease curing compounds and other foreign matter by sandblasting, mechanical abrasion.  If acid etching is used follow with abrasive or mechanical abrasion. Remove water and dust from all surfaces with an oil free blast, or vacuum, immediately prior to application.  STEEL: Prior to sand blasting remove all grease, dirt and other contaminants from the surface. Grind sharp edges to a minimum radius of 1/8 inch. Remove all weld splatters. Sandblast to a white metal finish according to SSPC-SP-5-63 or NACE standard TM-01-70 with a minimum anchor profile of 3 mils.

MIXING

Mix ratio is two parts by volume base ("A") to one part by volume hardener ("B").

APPLICATION

PRODUCT #OSVX3110can be applied by brush, roller or airless spray equipment. PRODUCT #OSVX3110 is designed to be spray applied at 10 to 15 mils per coat. Relative humidity during the coating process should be a maximum of 90% for application to commence.

A minimum of two coats is recommended. If the second coat is applied before the first coat cures, no surface preparation is required. Simply apply the second coat maintaining the required mils per coat. However, if the first coat has cured more than 24 hours, the first coat must be brush blasted prior to the second coat.

CLEANING

Clean all equipment immediately after use with MEK or acetone.

CAUTION

WARNING! A Component contains epoxy resin. DANGER! B Component contains alkaline amines; strong sensitizer. May cause skin sensitization or other allergic responses. Use with good ventilation, particularly if material is heated or sprayed. Prevent all contact with skin or eyes. Wear protective clothing, goggles, gloves and/or barrier creams. Keep container closed when not in use. Wash thoroughly after handling.

FIRST AID: In case of skin contact, immediately wash with soap and water. In case of eye contact, flush eyes with copious amounts of water for at least fifteen (15) minutes. Remove contaminated clothing and shoes. If irritation persists, seek medical attention. Wash clothing before reuse.

FOR INDUSTRIAL USE ONLY

KEEP AWAY FROM CHILDREN

Other customers who visited this page also visited:

Proper mixing and installation is critical to the optimal success of all product.  See Installation Tips, Techdata, & MSDS for more details on our products.  Be sure to contact us with any questions and/or concerns that you have.

For more information please contact:

Epoxy.com
A Division of Epoxy Systems, Inc
20774 W. Pennsylvania Ave.
Dunnellon, Florida 34431
Hundreds of Systems,
Since 1980 - 35 years
Florida & Vermont
USA


Customer and Technical Support Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time).
Closed 12 Noon-1PM Eastern Time for Lunch

321-206-1833  Customer Service - Ordering and Order Status
                         Katey Fontaine, VP - Customer Service Director
                         sales@epoxy.com

                        Technical Support
352-533-2167  Norm Lambert, President - Technical Support Director 
                         info@epoxy.com

352-489-1666  Accounting and Administration
                         Debby Lambert, CEO, and CFO
                         office@epoxy.com

352-489-1625   Fax line to all Departments

We accept MasterCard, Visa, American Express, Discover, Wire Transfers, and Cashiers Checks

Copyright © 1994-2015 - Epoxy Systems Inc. DBA Epoxy.com  - Commercial, Industrial, and Residential Resins Since 1980

/